The content in the next paragraphs about How to Install a Bathtub Yourself is quite intriguing. Check it out for yourself and figure out what you think of it.
Setting up a bathtub isn't exactly brain surgery, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a new one is also a moderately hard job. If the old tub is readily obtainable, the job can move speedily; if you need to open a wall surface to eliminate the old tub and also place the new bath tub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and also embeded in the new one. Make sure you have actually qualified on your own for the task and fit trying it. Instead of working with a specialist to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might require an expert plumber to make tube links.
This short article will certainly aid you set up a new tub in your bathroom if you have actually currently acquired a new tub as well as do not need to alter the plan of your previous water pipes.
Your tools as well as product checklist ought to consist of the following:
Preparing for the Installment
Firstly, the sustaining frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must now prepare to be suited its final placement.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is detach the supply of water. After doing so, activate the faucets to drain any kind of water remaining in the system. The procedure of eliminating the existing faucets can be quite bothersome because of the restricted accessibility that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, put the tub in the required position. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four little points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the spirit level as well as adjusting the feet on the bathtub till the level reviews degree.
To set up taps, fit the bottom of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the supply of water and also inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill the tub as well as likewise check the overflow electrical outlet and the regular outlet for leakages.
Lastly, fix the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used at the very least when as this will settle it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the supplier offered backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind needs to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to allow for the motion experienced when the bathtub is in use. The sealant can split rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the market. It is a good idea to fit the floor tiles utilizing waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid person who reads on How to Install a Bathtub, I think sharing that piece of content was appropriate. Do you know about somebody who is fascinated by the niche? Be sure promote it. Many thanks for taking the time to read it.
About This